Size: 1/2”to 24”
Material: Stainless Steel,Carbon Steel,Alloy Steel,Alloy Steel,Duplex Stainless Steel and so on
Standard: ASME, DIN , EN, BS, ISO, JIS
Pressure: Class: 150,300,400,600,900,1500 and 2500 PN: 2.5,6,10,16,25,40,64 and 160,5K - 40K and so on
Production technique: Forged
Connect Type: Weld
Applications: Petroleum, chemical, power, gas, water, line pipe, heat exchanger,Ship building, construction, etc
Origin: Zhejiang, China
Packaging & Delivery
Packaging Details: Seaworthy plywood case or as customer requests
Delivery Detail: 5 - 10 days after receiving the deposit
Stainless Steel: ASTM A403 WP304, 304L, 310, 316, 316L, 321, 347, 904L
Carbon Steel: ASTM A234 WPB, WPC ASTM A105 WPHY 42, 46, 52, 56, 60, 65, 70
Alloy Steel: ASTM A234 WP1, WP5, WP9, WP11, WP22, WP91
Duplex Stainless Steel: ASTM F51, 2205, F53, 2507, etc
Other: According to your needs
Standard: ASTM, DIN, EN, BS, ISO, JIS , etc
What is Lap Joint Flanges?
LF flange called are used on piping fitted with lapped pipe or with lap joint stub ends the combined initial cost of the two items being approximately one-third higher than that of comparable welding neck flanges. Their pressure-holding ability is little, if any, better than that of slip-on flanges and the fatigue life of the assembly is only one-tenth that of welding neck flanges. The f53 lap joint flanges with the stub end assembly are normally used in systems requiring frequent dismantling for inspection and cleaning and where the ability to swivel flanges and to align bolt holes materially eases the erection of large diameter or unusually stiff piping. 2507 Lap Joint flanges have certain special advantages: Freedom to swivel around the pipe facilitates the lining up of opposing flange bolt holes. Lack of contact with the fluid in the pipe often permits the use of inexpensive carbon steel flanges with corrosion resistant pipe. In systems which erode or corrode quickly, the flanges may be salvaged for re-use.
Slip on flanges with a hub have published specifications that range from 1/2" thru 24". Sizes above 24" are produced as lap joints to slip on dimensions. Footo Mfg provides 2507 Lap Joint flanges in all material grades, specifications and sizes.
Footo Mfg manufactures lap joint flanges in all steel material grades, including Super duplex stainless steel lap joint flanges, stainless steel lap joint flanges and alloy lap joint flanges. Footo Mfg also has many different lap joint flanges in stock and ready to ship. Footo Mfg can also manufacture custom pipe flanges according to customer specifications.
Materials For Lap Joint Flange
The most common materials used in flanges produced is carbon steel, super duplex stainless steel, duplex stainless steel, stainless steel, cast iron, aluminium, brass, bronze, plastic etc.
In addition, flanges, like fittings and pipes, for specific purposes sometimes internally equipped with layers of materials of a completely different quality as the flanges themselves, which are "lined flanges".
The material of a flange, is basically set during the choice of the pipe, in most cases, a flange is of the same material as the pipe.
Installation of 2507 LAPJOINT Flange
Center the gasket on the flange. This is extremely vital where raised faces are involved. Note: standard ANSI ring gaskets, when cut properly, should center themselves with the bolts in place.
Use a torque wrench and well-lubricated fasteners with hardened flat washers to ensure correct initial loading.
Tighten bolts to compress gasket uniformly. This means going from side to side around the joint, in a star-like crossing pattern.
All bolts should be tightened in one-third increments, according to proper bolting patterns. Retorque 12 to 24 hours after start-up, whenever possible.
All applicable safety standards including lockout/tagout procedure should be observed.
Never use liquid or metallic based anti-stick or lubricating compounds on the gaskets. Premature failure could occur as a result.
1.More than 20 years’ rich experience in manufacturing flange;
2.Strong technical force, fully equipment and steady development;
3.Perfect R&D, production, sales and after-sales service systems.
4.Good quality, fast delivery, promised stock notification in advance etc.
You can visit this website: www.cnfooto.com.
If any inquiry about products, please feel free to contact us firstname.lastname@example.org